Study of The Ceramic Cutting Tool Performance Using Double Rake Face

Suha K. Shehab; Ethar M. Mubarak

doi:10.24237/djes.2008.01101

Authors

Suha K. Shehab Department of Power Electrical Engineering College of Engineering, University of Diyala, Iraq
Ethar M. Mubarak Institute of Technical Technology of Baghdad, Iraq Foundation of Technical Education

Keywords:

ceramic, cutting tool, finite element.

Abstract

The objective of this work is to study the effect of the types of ceramic cutting tools on the cutting performance by using double rake tooling. The simulation in this research concerned with the initial cutting process using contact with the workpiece state.The results show that the concept of double rake tooling design proved to be the cutting performance of cutting process. It is also proved, that for every cutting condition, there is an optimum geometry and material of cutting tool. This work shows that ceramic material of metal cutting tools has better performance from cemented carbide tools comparing with other previously published papers.

Downloads

Download data is not yet available.

References

Erik Oberk, Franklin D.Jones, Holbrook L.Horton, and Henry H.Ryffel, "Machineryُ s Handbook 28th Edition", Industrial Press Inc., New York, pp.720-757, 2008.

Deweck, O., and Kim, Y., " Finite Element Method “, Massachusetts Institute of Technology ,pp.1-26, 2004 .

Altan, T.,Yen ,Y.ch , and Anurag , J., “A Finite Element Analysis of Orthogonal Machining Using Different Tool Edge Geometries”, ( ERC /NSM ) , the Ohio state university , USA , pp.1-15, 2002 .

Strenkowski, J.S.,and carrol III , J.T., “ A Finite Element Model of Orthogonal Metal Cutting” , Trans , Journal of Engineering for Industry , Vol .107 , No.4,pp.349-354 , 1985

Strenkowski, J.S., and Carrol III, J.T., “Finite Element Models of Orthogonal Cutting with Application to Single Point Doamond Turning”, International Journal of Mechanical Science, Vol .30 , No.12 , pp.899-920 , 1988.

Ozel , T., “Development of A predictive Machining Simulator for Orthogonal Metal Cutting process”, 4th International conference on Engineering Design and Automation , U.S.A.pp.1-7 , 2000

Maan .A.T. “Finite Element Simulation of Chip Formation and Comparison with Machining Experiments”, Ph .D Thesis , University of Technology / Baghdad , 2000 .

Lafta , A.F. “The Cutting Performance of Sailon Ceramic Tool” , Ph.D. Thesis , University of Aston , September , 1983 .

Hearn, E.J., “Mechanics of Materials”, pergamon press , 1st ,1977 .

Ethar M. Mubarak, “Study of The Cutting Tool Performance Using Double Rake Tolling”, M.Sc. thesis, The Technical College-Baghdad, 2005.

Ozel , T., “ Modeling of Hard Part Machining: Effect 0f Insert Edge Preparation in CBN Cutting Tools”, Journal of Materials Processing Technology, Vol.141,pp.284-293, 2003.

Ozel , T., “Process Simulation Using Finite Element Method-Prediction of Cutting Forces, Tool Stresses and Temperature in High Speed Flat End Milling”, International Journal of Machine Tools and Manufacture, Vol40, pp.713-738, 2000.

Chang, Ch. Sh., " A Force Model for Nose Radius Worn Tools with A Chamfered Main Cutting Edge", International Journal of Machine Tools and Manufacture Vol.38,pp. 1467-1498, 1998.

Yasin,.A. “Prediction of Cutting Tool Performance with Double Rake Geometry Using Finite Element Technique”, MSc. Thesis, Baghdad University, 2004.

P Joyot, R Rakotomalala, O Pantale, M Touratier and N Hakem, “A Numerical Simulation of Steady State Metal Cutting”, Journal of Processing Mechanics Engineering, Vol 212, No.C5, pp331-341, 1998.

M.M. Ahmad, R.T. Derricott and W.A. Drapert, “A Photoelastic Analysis of The Stresses in Double Rake Cutting Tools”, International Journal of Machine Tools Manufacturing”, Vol.29, No.2, pp.185-195, 1989.

K.Shintani, M.Uekit and Y.Fujimura, “Optimum Tool Geometry of CBN Tool for Continuous Turning of Carburized Steel”, International Journal of Machine Tools Manufacturing”, Vol.29, No.3, pp.403-413, 1989.