Using Intelligent Technique Rbfnn for Prediction Recognition of Tool Wear in Hard Turning

Akeel Ali Wannas

doi:10.24237/djes.2013.06302

Authors

Akeel Ali Wannas
some@some.com
Mechanical Engineering Department, University of Technology

Keywords:

RBFNN, wear, hard turning, applications, transmission, components

Abstract

Hard turning technology has been gaining acceptance in many industries throughout the last 2decades. The trend today is to replace the slow and cost-intensive grinding process with finish hard turning in many industrial applications such as bearings, transmission shafts, axles and engine components, flap gears, landing struts and aerospace engine components. In this study, Radial Basis Function Neural Network (RBFNN) model has been developed for the prediction of the status of the tool wear. Learning data was collected from Experimental setup. The neural network model has 3 input nodes and one output representing process Modeling correlates process state variables to parameters. The process input parameters are Feed rate (F), cutting Speed (S) and Depth of cut (Dc). The process output is state Variable (Vb). Regression analysis between finite element results and values predicted by the neural network model shows the least error.

Downloads

Download data is not yet available.

References

- Hashimura, M., Y. Chang and D. Dornfeld, “Analysis of burr formation mechanism in orthogonal cutting”, J. Manufacturing Sci. Eng., 121: 1-7, 1999. DOI: https://doi.org/10.1115/1.2830569

- Reisner, S. and B. Vogt, “Process converted from grinding to hard fine turning” Ind. Diamond Rev., 3: 62-63/65, 2003.

- Matsumoto, Y., F. Hashimoto and G. Lahoti, “Surface integrity generated by precision hard turning” Ann. College Int. Pour la Recherche en Producerique (CIRP), 48 (1): 59-62, 1999. DOI: https://doi.org/10.1016/S0007-8506(07)63131-X

- König, W., M. Klinger and R. Link, “Machining hard material with geometrically defined cutting edges-field of applications and limitations” Ann. College Int. Pour la Recherche en Producerique (CIRP), 39 (1): 61-64, 1990. DOI: https://doi.org/10.1016/S0007-8506(07)61003-8

- Liu, K. and S.N. Melkote, “Finite element analysis of the influence of tool edge radius on size effect in orthogonal micro-cutting process”, Int. J. Mech. Sci., 49 (5): 650-660, 2007. DOI: https://doi.org/10.1016/j.ijmecsci.2006.09.012

- Bagshaw, R.W. and S.T. Newman, “Manufacturing data analysis of machine tool errors within a contemporary small manufacturing enterprise”, Int. J. Machine Tools Manufacture, 42 (9): 1065-1080, 2002. DOI: https://doi.org/10.1016/S0890-6955(02)00027-5

- Thiele, J., S. Melkote, R. Peascoe and T. Watkins, “Effect of cutting-edge geometry and workpiece hardness on surface residual stresses in finish hard turning of AISI 52100 steel”, Trans. ASME J. Manufacturing Sci. Eng., 122: 642-649, 2000. DOI: https://doi.org/10.1115/1.1286369

- Li, X. and X. Yao, “Multi-scale statistical process monitoring in machining”, IEEE. Trans. Ind. Elec., 52 (3): 924-927. DOI: 10.1109/TIE.2005.847580, 2005. DOI: https://doi.org/10.1109/TIE.2005.847580

- Sohrab, K., I. Hassanzadeh and M.B.B. Sharifian, “Modified adaptive discrete control system containing neural estimator and neural controller”, AI in Eng., 14 (1): 31-38. DOI: 10.1016/S0954-1810 (99)00017-5, 1999. DOI: https://doi.org/10.1016/S0954-1810(99)00017-5